How do you install TITAN RV fan to the electric source?
There are two nacked wires, a red (positive polarity) and black wire (negative polarity) that leads from the control panel of the fan. Connected those to the 12V power supply and hook those wires to the same polarity source (positive to positive/ negative to negative).
The illustration of fan cable
Naked power cable side (lead from the controller)The black wire is negative and the red one is positive. Connect those to the power supply of 12V DC. Please take care of the correct polarity (positive to positive/ negative to negative). Please ensure that power is 12V DC and make sure the power supply works normally before connecting.
Temperature sensor (lead from the controller)There is a probe to detect the temperature of the environment near the evaporator of the refrigerator. We suggest to place the sensor in about 1 inch freely suspended to the evaporator because there is the warmest area.
Fan cable (lead from the controller)The length of 3-pin fan cable is 2M. Please connect it to the 3-pin Y-cable.
Y-cableThe 3-pin Y-cable powers the double fan. It combines fan and speed controller. Please notice that the fan cable need to be connected with the speed controller. Don’t connect it anywhere else, otherwise speed controller and fan will not work properly. The fan splitter cable is specially designed to be only compatible with the speed controller.
- Other FAQ
- Yes. TITAN RV fan series are designed to help cool down the RV refrigerator, and we advise to be installed on close to evaporator of the refrigerator to improve ventilation. But the temperature of fridge cooling fins would not be over 70℃. Please carefully notice the surrounding temperature. There is a probe to detect the temperature of the environment near the evaporator of the refrigerator. We suggest to place the sensor in about 1 inch freely suspended to the evaporator because there is the warmest area.Yes. TITAN RV fan series has the product to be designed to the outside fridge vents. We could also customize unique RV fan for your need. You can install the TITAN RV fan in both lower and upper ventilation vents. The correct mounted way is that bottom RV side vent mounts the fan to push fresh air in, and RV upper side vent near the top mounts the fan to exhaust the heat out. The way of installation complies with the air circulation rules: hot air rises and cold air sinks. It is the key to quickly boost the air circulation of the RV fridge.There are various places with the need of ventilation such as RV fridge, RV window, Bathroom& Toilet, and kitchen. According to the need of RV ventilation, TITAN designs a series cooling fan solution to RV design, RV customer. You could check the information in other page.Yes. You just have to place it in vent area after taking off the cover and modify how you would/will secure it. It is very easy and does help. But you might have to lengthen the wires. We have a video which the fan is be mounted to the roof vent. You can make it as reference.There are two nacked wires, a red (positive polarity) and black wire (negative polarity) that leads from the control panel of the fan. Connected those to the 12V power supply and hook those wires to the same polarity source (positive to positive/ negative to negative).TITAN Multi-purpose rack fan series is designed to DIY mounted. You can depend on the function you want to choose such as timer setting, waterproof function, reversible airflow function, etc. They can be installed on fridge vent, top roof vent, cabinet, table, side window as so on. Below is the differences chart for all series to refer.There also is some introduction video from YouTuber. You can make it as references.Fan speed varies from 45F to 113F, it is supposed to shut off below 45F but in reality neither one of mine ever shut off even down to freezing, they do reach maximum speed by 113F and above.Hello, owing to this product is DC fan, the amperage of the fan is low. I can offer you the rated current. of the fans. Please see below. Hope it is clear for you. Thank you.TTC-SC09(A) 90mm is 0.48 A. TTC-SC09(B) 120mm is 0.56 A. TTC-SC09(C) 140mm is 0.8 A. Maximum Output Current of the speed controller is 1A.The common RV fridge has two ventilation side vents, upper and bottom. The correct mounted way is that bottom RV side vent mounts the fan to push fresh air in, and RV upper side vent near the top mounts the fan to exhaust the heat out. The way of installation complies with the air circulation rules: hot air rises and cold air sinks. It is the key to quickly boost the air circulation of the RV fridge. You are based on to the need to mount them.No. Please do not attempt to revise the polarity. It would not change airflow by revising the polarity. It will only cause permanent damage to the fan controller.Please kindly check below instrucitons, and notice the voltages, wires, speed controller, and fan itself before installation.Owing to the probe is to detect outside air temperature, we suggest you could place the sensor near about an inch from the highest of heating rising. But you may research the heat of your place to ensure the proper placement.The speed controller can be mounted on any places. But we suggest you should place it from outside of vent, so that you can easily control and switch them according to different needs There are two ways to install the controller. You can drill a small hole and thread the wires through. Or you can attach the sticker on the wall.No. The fan speed would not increase the fan speed by connect over the power over 12 voltages. If you connect over 12 voltages, the fan may cause permanent damage.Please follow the bellow instruction to make a self-trobleshoopting. If there are still problems with the fan or speed controller, please kinldy contact us. We would assist you as fast as we could.Yes. The “Y” harness combines the two fans power leads. Nevertheless, please kindly notice that the fan cable need to connect with our speed controller and do not connect with others, or both of them would not work. The fan splitter cable is specially designed to compatible with the speed controller.No. The fan is not required to be installed battery. It has the power connector of 12 Volts.
According to the RV fridge venting system, it would produce over-heating while operating. If the RV fridge couldn’t cool down the temperature, the RV fridge would too hot to keep food fresh and cool. It has been caused a common thermal problem for RV owner or RV designer. TITAN RV fridge ventilation fan is able to assist you to improve the RV fridge thermal problem and customize different RV fridge fan.
TITAN RV fan could customize refrigerator side vent to accelerate RV fridge circulation. Installed a RV fan inside of evaporator could help the heat out quickly. It is an active way exposing the heat source and to exhaust the heat out or pull fresh air in of the RV fridge to boost the performance of the RV fridge efficient.
TITAN RV fan could customize refrigerator roof vent to improve RV fridge circulation. The rooftop vent is also the key to cool down the RV fridge temperature. The roof vent usually is made of UV-resistant to stand up against sun rays. The fan equipped with IP55 waterproof is identical to rooftop RV fridge vent fan. TITAN could also provide various function design such as the auto temperature detection and timer setting to achieve the power saving.
RV skylights or roof window are a great option in any RV, providing natural light and fresh air to the areas. The main places of RV skylights or roof window are kitchen, living room, shower/bathroom and sleeping rooms, etc.
- 2018 Computex Taipei
TITAN will participate in Computex Taipei held on June 5- June 9, 2018. Show our latest cooling fan and related computer cooler.Read More
- USB Tower Cooling Fan for Car & Baby Stroller
This is a USB tower cooling fan for car fan, baby stroller fan, wheelchairs fan or office fan etc.Read More
- USB Ultra-Silent Cooling Fan
Equipped with 140mm professional cooling fan. It is strong airflow, ultra-quiet, and log life time.Read More